[Jul-2021] Pass Network Appliance NS0-519 Exam in First Attempt Guaranteed!
Full NS0-519 Practice Test and 60 unique questions with explanations waiting just for you, get it now!
NEW QUESTION 15
An administrator enabled the iSCSI protocol on an SVM and created a LUN for a VMware ESXi server.
After the administrator performs a rescan, the LUN is not visible on the host.
Which statement describes how to solve this problem?
- A. Create an igroup, add the WWPN of the host initiator, then map the LUN to the igroup.
- B. Create an igroup, add the iSCSI IQN, then map the LUN to the igroup.
- C. Perform a takeover/giveback of the controller that is hosting the LUN.
- D. Enable ALUA support on the VMware host.
Answer: B
NEW QUESTION 16
You have a new 2-node AFF All SAN Array A700 cluster serving iSCSI LUNs. You are asked to test failures of the front-end protocol connections.
Which two actions satisfy the failure criteria? (Choose two.)
- A. Pull an Ethernet cable from a Linux host.
- B. Disable Snapshot policies.
- C. Pull an Ethernet cable from a storage port with a cluster LIF.
- D. Perform a storage controller failover.
Answer: A,D
NEW QUESTION 17
Click the Exhibit button.
A customer has a 4-node AFF A700 cluster that uses ONTAP 9.7. The customer's environment has the Emulex LP31004-M6 and Emulex LPe32002-M2 HBAs.
Referring to the exhibit, using the NVMe protocol, which two host operating systems would be supported? (Choose two.)
- A. SLES 15 64-bit
- B. Microsoft Windows Server 2012 R2
- C. SLES 12 SP3 64-bit
- D. RHEL 7.5 64-bit
Answer: A,C
NEW QUESTION 18
Click the Exhibit button.
You have an 8-node AFF A800 ONTAP 9.7 cluster. You have sixteen SVMs that serve NVMe namespaces using two 32 Gb FC ports per AFF A800 controller.
Referring to the exhibit, what is the maximum number of NVMe data LIFs that are supported on this cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 19
Click the Exhibit button.
Referring to the exhibit, which switch in the fabric is the principal switch?
- A. sw6
- B. sw5
- C. sw4
- D. sw10
Answer: A
NEW QUESTION 20
Click the Exhibit button.
You issue the cfgshow command on one of your Brocade switches and notice that there is no zoning listed under the Effective configuration. When you attempt to use the fcping command from the initiator to the target, the command fails.
Referring to the exhibit, what are two problems? (Choose two.)
- A. The default zone access is set to allow even though zoning is defined.
- B. There is no zoning configured, and the default zone's access is set to No Access.
- C. There is no alias for either the initiator or the target.
- D. There is no zone defined that has both the initiator and target in a common zone.
Answer: B,D
NEW QUESTION 21
An additional LUN is required to be created and attached to an existing VMware ESXi environment. You are asked by a VMware administrator what NetApp software would validate multi-path connections to a newly presented FC LUN.
In this scenario, which NetApp software is required?
- A. You must install Active IQ Config Advisor.
- B. You must install the NetApp VSC.
- C. You must install Active IQ OneCollect.
- D. You must Install the DSM onto the virtual machine.
Answer: D
NEW QUESTION 22
Click the Exhibit button.
Referring to the exhibit, which step must be performed to make LUN lun0 available to hosts in igroup linux1?
- A. node-01 and node-02 must be removed from the list of reporting nodes.
- B. lun0 must be mapped to linux1.
- C. lun0 must be brought online.
- D. node-03 and node-04 must be added to the list of reporting nodes.
Answer: C
NEW QUESTION 23
An administrator has taken over managing an AFF A320 4-node SAN environment with several attached hosts. The administrator is asked to inventory the environment before performing firmware updates.
In this scenario, which two tools would satisfy the requirement? (Choose two.)
- A. Brocade SAN Health Check
- B. Active IQ OneCollect
- C. Active IQ
- D. Upgrade Advisor
Answer: B,D
NEW QUESTION 24
Click the Exhibit button.
Referring to the dual-fabric cabling diagram shown in the exhibit, which scenario explains why the customer's iSCSI host experienced a SAN outage with a LUN on Node 2?
- A. iSCSI LIFs were configured on all nodes, the SLM reporting nodes list included Node 1 and Node 2, and Node 1 went down.
- B. iSCSI LIFs were configured on Node 1 and Node 2 only, the SLM reporting nodes list included Node 1 and Node 2, and Switch 1 went down.
- C. iSCSI LIFs were configured on all nodes, the SLM reporting nodes list included all nodes, and Node 1 and Node 2 went down.
- D. iSCSI LIFs were configured on Node 2 only, the SLM reporting nodes list included Node 1 and Node 2, and the cable connecting the host to Switch 1 went bad.
Answer: C
NEW QUESTION 25
Click the Exhibit button.
You have an existing legacy Fibre Channel SAN environment and have deployed an ONTAP AFF A800 cluster. You are planning to migrate a NetApp Foreign LUN Import using the existing SAN environment.
Referring to the exhibit, how must the UTA2 ports be configured?
- A. Configure the FCP to target mode.
- B. Configure the FCP to initiator mode.
- C. Configure the CNA to target mode.
- D. Configure the CNA to initiator mode.
Answer: B
NEW QUESTION 26
An administrator suspects abnormal operation and performance-related issues within a particular SAN environment. The administrator wants to further investigate the environment in terms of overall health, best practice recommendations, proactive remediation, and risk assessments, as compared to other SAN deployments.
Which tool should the administrator use to assess this information?
- A. Active IQ OneCollect
- B. Active IQ Config Advisor
- C. Interoperability Matrix Tool (IMT)
- D. Active IQ
Answer: B
NEW QUESTION 27
You are asked to increase the size of your existing 4-node FAS8060 cluster running ONTAP 9.7 software with four additional AFF A700 nodes.
Which tool enables you to confirm that this will be a valid addition?
- A. Active IQ OneCollect
- B. Active IQ Config Advisor
- C. Hardware Universe (HWU)
- D. Active IQ
Answer: C
NEW QUESTION 28
Which two SAN components are inventoried by Active IQ OneCollect? (Choose two.)
- A. power supply
- B. storage controller
- C. FC switches
- D. fans
Answer: B,C
NEW QUESTION 29
You are connecting an ISL between two Brocade switches on ports 20 and 21.
Which port-channel type should you configure?
- A. E_port
- B. F_port
- C. FL_port
- D. U_port
Answer: A
NEW QUESTION 30
You plan to use Foreign LUN Import (FLI) to migrate data from an older storage array to an ONTAP cluster. You have properly cabled the storage array and the NetApp nodes to your dual-fabric SAN.
Which two steps are required for this migration and cutover? (Choose two.)
- A. Add NetApp WWN target ports to the existing zones so that your hosts can access both storage arrays.
- B. Create two zones that contain the NetApp target ports and the host initiators ports, one for each fabric.
- C. Add NetApp WWN initiator ports to the existing zones.
- D. Create two zones that contain NetApp initiator ports and the source storage target ports, one for each fabric.
Answer: A,B
NEW QUESTION 31
You have a 2-node AFF A220 switchless cluster serving iSCSI LUNs. NetApp Volume Encryption (NVE) is enabled on all data volumes. You are asked to consolidate identical boot LUNs that are on both controllers. You need to nondisruptively consolidate LUNs with the highest storage efficiency.
In this scenario, which NetApp ONTAP technology accomplishes this task?
- A. LIF migrate
- B. aggregate relocate
- C. LUN move
- D. volume move
Answer: D
NEW QUESTION 32
You must ensure that a cluster that uses FabricPool has high availability,
What is required to accomplish this task?
- A. an IPspace that is dedicated to the FabricPool
- B. a cloud bucket
- C. four cluster LIFs
- D. a local failover policy for intercluster LIFs
Answer: D
NEW QUESTION 33
You are adding a new AFF A220 FIA pair to an existing FlexPod infrastructure that is using a pair of Nexus 9332PX switches. Due to rack space constraints, the AFF A220 is to be installed in an adjoining rack, and the distance from the back of the AFF A220 to the Nexus 9332PX switches is nine meters.
In this scenario, which 10Gbe cabling solution would you use to connect the AFF A220 to the Nexus 9332PX switches?
- A. LC/LC OM4 optical
- B. passive Twinax
- C. mini SAS
- D. active Twinax
Answer: D
NEW QUESTION 34
An administrator added the FCP protocol to an SVM and created a LUN for a Windows Server 2019 server. After a rescan, the LUN is not visible on the host.
Which two statements describe how to solve this problem? (Choose two.)
- A. Perform takeover and giveback of both controllers.
- B. Disable and enable the FC port with the attached host, causing a FLOGI.
- C. Create a zone with a single initiator and the target LIF's WWPN.
- D. Create an igroup, add the WWPN of the host initiator, and then map the igroup to the LUN.
Answer: C,D
NEW QUESTION 35
You have a new 2-node AFF All SAN Array A700 cluster serving iSCSI LUNs. You are asked to test failures of the storage back-end subsystem.
In this scenario, which two actions satisfy the failure criteria? (Choose two.)
- A. Disable Snapshot policies.
- B. Pull an Ethernet cable from a Linux host.
- C. Pull an Ethernet cable from a storage port with a cluster LIF.
- D. Perform a storage controller failover.
Answer: C,D
NEW QUESTION 36
You are an administrator of a multi-tenanted cluster which hosts multiple SVMs. One of your tenants requires management access to their SVM for SnapCenter to perform a backup. You are asked by the backup team to create a dedicated user account and management LIF for this purpose.
In this scenario, which LIF role would be associated with management access?
- A. Intercluster
- B. Cluster
- C. Data
- D. Node Management
Answer: D
NEW QUESTION 37
What information should you document about your storage fabrics? (Choose two.)
- A. name service
- B. Inter-Switch Links (ISLs)
- C. igroup name
- D. zoning configuration
Answer: B,D
NEW QUESTION 38
You have 20 hosts, each with a single connection to one FC target port of an ONTAP HA pair. Each initiator is configured to limit the number of SCSI commands to 64 for each initiator-target connection. You plan to add 20 more hosts with the same number of connections.
In this scenario, how should you configure the queue depth limit?
- A. The sum of all hosts' queue depths per each target port should be less than or equal to 2048.
- B. Each host's queue depth should be set to 128.
- C. The sum of all hosts' queue depths per each target port should be less than or equal to 4096.
- D. Each host's queue depth should be set to 64.
Answer: D
NEW QUESTION 39
......
Get Latest NS0-519 Dumps Exam Questions in here: https://www.realvalidexam.com/NS0-519-real-exam-dumps.html
